Get 100% Passing Success With True NS0-164 Exam! [Dec-2025]
Network Appliance NS0-164 PDF Questions - Exceptional Practice To NetApp Data Administrator ONTAP Professional Exam
NEW QUESTION # 57
To restore a qtree protected with SnapVault from the secondary storage system to the primary storage system, you can ______________. (Choose two.)
- A. overwrite the existing qtree on the primary storage system with DOT 7.3
- B. delete the existing qtree from the secondary storage system with DOT 7.3
- C. restore to a non existing qtree, with DOT 7. 2
- D. add the new qtree to the primary storage system with DOT 7.2
Answer: A,C
NEW QUESTION # 58
In a synchronous SnapMirror configuration, the source storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.
Which one of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:
- A. src con=3
- B. cksum=3s
- C. visibility_interval=3s
- D. outstanding=3s
Answer: D
NEW QUESTION # 59
Five minutes ago, you performed a single file SnapRestore on a large NFS file. 40% of your NFS users are now complaining about getting "stale file handles" for the file.
Which one of the following is the most likely cause of this problem, and the best procedure to correct it?
- A. This might be due to an NFS storage appliance and client version mis-match. Check to see that these users have the same version of the NFS client that existed at the time the snapshot was taken.
- B. These users are on a different subnet from the others. Start troubleshooting by checking their subnet.
- C. After a single file SnapRestore, NFS users have to reboot their systems. Have them reboot their systems.
- D. NFS users who try to access a reverted file without first reopening it might get a "stale file handle" error message. Have the users try to reopen the file and see if the problem is resolved.
Answer: D
NEW QUESTION # 60
Which two of the following NetApp storage appliances do not support the use of synchronous SnapMirror?
- A. F825
- B. F820
- C. F87
- D. FAS960
Answer: B,C
NEW QUESTION # 61
If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 62
Which two tools should an administrator use to monitor system performance in real time? (Choose two.)
- A. ActivelQ Unified Manager
- B. AetivelQ Conflg Advisor
- C. ONTAP CU
- D. ONTAP System Manager
Answer: C,D
NEW QUESTION # 63
Which option of the snap restore command allows you to specify a different directory, as long as the directory already exists?
- A. snap restore-r
- B. snap restore-c
- C. snap restore-s
- D. snap restore-d
Answer: A
NEW QUESTION # 64
When Data ONTAP creates a weekly, nightly, or hourly snapshot, the value of n (as shown by the UNIX Is command) is adjusted for all the weekly, nightly, or hourly snapshots. The higher the value of n. the_________the snapshot.
- A. least important
- B. older
- C. newer
- D. more important
Answer: B
NEW QUESTION # 65
To remove a cluster setup, you must perform the following steps.
1. Type cf disable.
2. Unlicense cluster.
3. Remove partner entries for network interfaces from the /etc/rc file.
4. Halt and make sine the partner-sysid is blank.
5. Power down and remove the cluster interconnect card.
6. Perform steps 1-5 above on the partner node.
- A. True
- B. False
Answer: A
NEW QUESTION # 66
Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pul data from the source appliance?
- A. snapmirror release
- B. snapmirror initialize
- C. options snapmirror.access
- D. options snapmirror.allow
Answer: C
NEW QUESTION # 67
The two copies of a SyncMirror volume are called_______. Each______is a physical copy of the same file system and consists of one or more RAID groups.
- A. plexes. plex
- B. volumes, volume
- C. qtrees. qtree
- D. snapshots, snapshot
Answer: A
NEW QUESTION # 68
Which command displays the disk ownership for both CPU modules in a FAS270C appliance?
- A. disk own -s
- B. vol status -r
- C. disk display-r
- D. disk show-v
Answer: D
NEW QUESTION # 69
Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner node, Node 2, can see all of Node 1s disk shelves.
Which one of the following features will cause Node 2 to monitor this error condition for a period of three minutes (by default), and then forcibly take over Node 1 if the error condition persists?
- A. Takeover on panic
- B. Auto enable of giveback
- C. Negotiated Fail Over
- D. cf.quickloop.enable
Answer: C
NEW QUESTION # 70
An aggregate is composed of twelve 36-Gigabyte disks. A drive fails and only 72-Gigabyte spare disks are available Data ONTAP will then perform what action?
- A. chooses a 72-Gigabyte disk and right-size it
- B. chooses a 72-Gigabyte disk and use it as is
- C. halts after 24 hours of running in degraded mode
- D. alerts you that there are no 36-Gigabyte disks and wait for one to be inserted
Answer: A
NEW QUESTION # 71
When using a Protection Manager policy to manage Open Systems SnapVault backups on a UNIX server, which three are valid objects to include in the data set? (Choose three.)
- A. a file
- B. The entire client
- C. A qtree
- D. A directory
Answer: A,B,D
NEW QUESTION # 72
......
NS0-164 dumps - ActualVCE - 100% Passing Guarantee: https://buildazure.actualvce.com/NetworkAppliance/NS0-164-valid-vce-dumps.html